Arduino Modules

View as Grid List
Sort by
Display per page

LM2596HVS DC to DC Adjustable Step Down Buck Converter Power Supply Module

03.00.24
Input voltage range: DC 4.5V to 53V (input voltage must be greater than the output voltage to 1.5V or more high. Could not boost)
ج.م.‏ 70.00

Bluetooth Module HC-05 , Serial TTL

03.02.26
The HC-05 is a class 2 Bluetooth module designed for transparent wireless serial communication. It is pre-configured as a slave Bluetooth device. Once it is paired to a master Bluetooth device such as PC, smartphone and tablet, its operation becomes transparent to the user. No user code specific to the Bluetooth module is needed at all in the user-microcontroller program.
ج.م.‏ 175.00

Bluetooth Module HC-06 , Serial TTL

03.01.26
Bluetooth UART RS232 serial converter Module Operating Frequency Band 2.4GHz unlicensed ISM band Bluetooth Specification V2.0+EDR Output Power Class 2 Operating Voltage 3.3V Host Interface USB/UART Audio Interface None Flash Memory Size 8Mbit. Features: CSR Bluetooth Chip Solution Bluetooth v2.0+EDR Compliant UART interface and with baud rate setup function Built-in antenna. Coverage up to 30ft. Incredible small size with 3.3V input, and RoHS Compliant Working current: While pairing 30mA, paired 8mA Frequency: 2.4GHz ISM band Baud rate is 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 user manually set up. Default Baud Rate: 9600,8,1,n Support for 8Mbit External Flash Onboard Support for 802.11 Co-Existence Product Description Storage Temperature: -40 to 85 degrees Celsius Size : 28 mm x 15 mm x 2.35 mm Used for GPS navigation system, water and electricity gas Automatic Reading Meter, The industrial field in control system The factory default parameters: Baud rate: 9600, N, 8, 1. Pairing code: 1234 AT command set as follows: 1, Test communication Send: AT (return OK, A seconds press once again) Return: OK 2, Change Bluetooth serial interface communication baud rate Send: AT + BAUD1 Return: OK1200 Send: AT + BAUD2 Return: OK2400 1---------1200 2---------2400 3---------4800 4---------9600 5---------19200 6---------38400 7---------57600 8---------115200 9---------230400 A---------460800 B---------921600 C---------1382400 Not recommended in more than 115200 baud rate, the signal interference will make the system not stability 3, change bluetooth name Send: AT + NAMEname Return: OKname Parameter name: will set the current name, which was the name of the search to Bluetooth. Within 20 characters. Example: send AT + NAME bill_gates Back to OKname now Bluetooth name is bill_gates Parameters can power lost save, modify it only need once. The PAD service can see change Bluetooth name 4, Change Bluetooth pairing password Send: AT + PINxxxx Return: OKsetpin Example: send AT + PIN8888 Back to OKsetpin now Bluetooth pairing password is 8888, module's default password g is 1234. Parameters can power lost save, modify it only need once.
ج.م.‏ 185.00

5mW Laser Module emitter - Red Line

03.01.52
Specifications Output Power: Min 2.5mW, Typical 3.0mW, Max 5.0mW Working current: Min 10mA, Typical 20mA, Max 25mA Working voltage: Min 2.3VDC, Typical 4.5VDC, Max 8.0VDC Wavelength: 650nm Working Temperature: Min -15℃, Typical 25℃, Max 35℃ Storage Temperature: Min -20℃, Max +25℃ Focused Dot width:<2mm spotting 3 meters away. Outline Dimension: 12mm(Diameter) x 35mm(Length) Practical test for point head: reflection visible to random target >1000m Cautions: Class III, avoid direct eye exposure to beams.
ج.م.‏ 85.00

Serial Converter TTL UART on CP2102 USB Module Board

03.03.46
CP2102 its high integration, built-in USB2.0 full-speed function controller, USB transceiver, crystal oscillator, EEPROM, and asynchronous serial data bus (UART), supports full-featured modem signals, without any external USB device. CP2102 with other USB-UART adapter circuit works similar to the PC through the driver's USB port into a virtual COM port in order to achieve the purpose of expansion.
ج.م.‏ 95.00

3-Axis Gyroscope & Accelerometer Module GY-521 - 16-Bit Digital Output, I2C Interface - MPU6050

GY-521 MPU6050 6DOF 3-Axis Gyroscope and Accelerometer Module is a carrier board based on MPU-6050 sensor which contains an accelerometer and a gyroscope. MPU-6050 sensor contains a MEMS accelerometer and a MEMS gyro in a single chip. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel. Therefore it captures the x, y, and z channel at the same time. The sensor uses the I2C-bus to interface with microcontrollers.
ج.م.‏ 95.00

Laser sensor Module 650nm 6mm 5V 5mW Red Laser Dot Diode KY-008 for Arduino

03.01.38
LASER SENSOR MODULE 650NM 6MM 5V 5MW RED LASER DOT DIODE KY-008 FOR ARDUINO OPERATING VOLTAGE 5V POWER 5MW WAVELENGTH 650NM
ج.م.‏ 60.00

Bigtreetech New 3D printer hot bed Power expansion board/MOS tube high current load module for 3D printer

This module can be used in both Chitu motherboard. The motherboard shows in the pictures is NOT included in the shipping list.
ج.م.‏ 150.00

Laser Receiving Module

03.02.38
LASER RECEIVING MODULE
ج.م.‏ 75.00

Relay Module 4 Channel

03.00.48
THIS IS A 5V 4-CHANNELS RELAY MODULE, IT CAN BE CONTROLLED DIRECTLY BY A WIDE RANGE OF MICROCONTROLLERS SUCH AS ARDUINO, AVR, PIC, ARM AND MSP430.
ج.م.‏ 100.00

RC522 RFID Card Reader Module Kit for Arduino

03.00.34
THIS IS THE RFID 13.56 MHZ RFID MODULE BOARD KIT, THE MODULE BOARD THAT USED ON THIS KIT HAS RC522 INTEGRATED CIRCUIT THAT DRIVES THE 13.56 MHZ RADIO FREQUENCY. THE MF RC522 IS A HIGHLY INTEGRATED TRANSMISSION FOR CONTACT-LESS COMMUNICATION THAT RUNS ON 13.56 MHZ IT SUPPORT ALSO THE ISO 14443A/MIFARE MODE LIBRARY. THIS RFID KIT HAS INCLUDED THE S50 RFID CARD AND ID TAG.
ج.م.‏ 190.00

Stepper Motor Driver A3967 Module

03.00.53
Note: Do not connect or disconnect a motor while the driver is energized. This will cause permanent damage to the A3967 IC
ج.م.‏ 85.00

12V LED Automatic Control Switch Relay Module

03.03.37
Brand : Other Type : Microcontroller Boards
ج.م.‏ 210.00

Bigtreetech New 3D printer hot bed Power expansion board/Heatbed power module/MOS tube high current load module for 3D printer

03.00.44
*Completely solve the hot bed power is too large and the load current issue *Under the premise of normal cooling, it work stable under I(Max)=10A, the current must not exceed 10A while the process working *If you need anything greater or equal to 10A this module is a must! For example, if your total power usage is 120W and you have 12V power supply, then it means at least 10A is needed (10X12=120W). *As ChiTu controller board is only capable of 10A this setting will not work. To make it work,you need this extra power module. *If the power is used improperly, it may burn. *Dimensions: 60*50mm
ج.م.‏ 175.00

Relay Module Two Channel

03.01.47
This is a 5V 2-Channels Relay module, It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and MSP430.2 relays are included in this module, with “NC” ports means “Normally connected to COM” and “NO” ports means “Normally open to COM”.This module is also equipped with 2 LEDS to show the status of relays.Maximum load: AC 250V/10A, DC 30V/10ADriving ...
ج.م.‏ 65.00

XL6009 Step-up Power Module DC-DC Converter 4.5-32V -5-55V

03.01.108
Brand : Adorne Type : Electronic Accessories
ج.م.‏ 195.00

solid state relay 4 out put

03.00.37
Brand : Arduino Type : Electronic Accessories
ج.م.‏ 255.00

High Power LED Module "Power 3W"

03.00.52
Color temperature: Warm White 3000-3200K / white 6000-6500K Forward current: 700MA Luminous flux: White 180-200LM (lumens) Forward voltage: 3.3 - 3.6 V Reverse voltage: 5V Power: 3W Viewing angle: 180° Working temperature: -20° to 60° Brand : Other Model Number : ahplm54869
ج.م.‏ 30.00

150W DC to DC Step UP Boost Converter module

03.00.108
SPECIFICATIONS: INPUT VOLTAGE: DC 10V-32V. OUTPUT VOLTAGE: DC12V-35V(ADJUSTABLE). OUTPUT CURRENT: 5A (MAX). INPUT CURRENT: 8A (MAX) (MORE THAN 8A PLEASE STRENGTHEN HEAT SINK). OUTPUT POWER: NATURAL COOLING 100W (MAX), STRENGTHENING COOLING 150W (MAX) REAL POWER. CONVERSION EFFICIENCY: 94% (WHEN INPUT 19V 2.5A OUTPUT 16V, REFERENCE). OUTPUT RIPPLE: 2% (MAX). WORKING TEMPERATURE: INDUSTRIAL (- 40 ¡Ã C TO 85 ¡Ã C) ( ENVIRONMENTAL TEMPERATURE, MORE THAN 40 DEGREES, PLEASE REDUCE POWER TO USE, OR - ENHANCE COOLING). FULL-LOAD TEMPERATURE: 45 DEGREES. NO-LOAD CURRENT: 25MA TYPICAL. VOLTAGE REGULATION: ¡À 0.5%. LOAD REGULATION: ¡À 0.5%. DYNAMIC RESPONSE SPEED: 200US 5%. SHORT CIRCUIT PROTECTION: NO (PLEASE INSTALLS THE FUSE OR PROTECTION CIRCUIT AT INPUT PARTS). INPUT REVERSE PROTECTION: NO (PLEASE COMPLY WITH A REVERSE PROTECTION OR CONNECT A DIODE AT INPUT PARTS.) SIZE: 65MM X 35MM X 21MM 150W DC to DC Step UP Boost Converter module
ج.م.‏ 100.00

AC-DC 5V700mA 3.5W Power Supply Buck Converter Step Down Module

03.01.24
Type : Electronic Accessories Output Over Power Protection Short circuit protection Temperature protection Current protection Dimensions:3cm x 2cm x 1.8cm
ج.م.‏ 70.00