Arduino

View as Grid List
Sort by
Display per page

Sensor Shield v2 for arduino Mega 1280 or 2560

03.00.04
THIS SHIELD BOARD PLUGS ON TOP OF AN ARDUINO MEGA (1280 OR 2560) AND MAKES IT EASY TO CONNECT TO ALL THE MANY DIGITAL INPUTS AND OUTPUTS AND THE ANALOG INPUTS. THIS IS PARTICULARLY GOOD FOR HIGH I/O PROJECTS WITH MANY LEDS OR CONTROLS WHERE CONNECTIONS TO THE MEGA CAN BE A MAJOR PROBLEM.
ج.م.‏ 120.00

SYB-830 Tie-Point Breadboard

03.0000.0888888
MODEL: MB-102 IDEAL FOR HIGH FREQUENCY AND LOW NOISE CIRCUITS INTERCONNECT ANY COMPONENTS WITH 20-29 AWG(0.3-0.8 MM) WIRE SPECIAL DESIGNED SPRING CLIP OVER 5,000 INSERTION CYCLES NICKEL PLATED, SILVER PLATED AND GOLD PLATED AVAILABLE
ج.م.‏ 45.00

Arduino Pyroelectric Infrared IR PIR Motion Sensor Detection Module

03.00.110
Arduino Pyroelectric Infrared IR PIR Motion Sensor Detection Module This is a highly integrated module popularly used for entry detection, it can simplely and easily to adopt in system. There are two adjustable potentiometer on the module, you can use them to change the trigger sensitivity and the duration of the trigger signal. This is a highly integrated module popularly used for entry detection, it can simplely and easily to adopt in system. There are two adjustable potentiometer on the module, you can use them to change the trigger sensitivity and the duration of the trigger signal. Specification : Input Voltage: DC 4.5-20V Static current: 50uA Output signal: 0,3V or 5V (Output high when motion detected) Sentry Angle: 110 degree Sentry Distance: max 7 m Shunt for setting override trigger: H - Yes, L - No
ج.م.‏ 60.00

HD-U62 Support 7-color Led Display Controller

03.02.03
Type : 3D Printer Accessories Brand : Other
ج.م.‏ 160.00

LCD 128x64 Smart LCD Controller with SD Card interface

01.00.06
EQUIPMENT ETC. LCD CONTROL PANEL THROUGH WHICH YOU CAN ACHIEVE SPOOLING IS THE 3D MODEL GCODE FILES ARE COPIED TO THE SD CARD, AND THEN PRINT THE FILE VIA THE LCD CONTROL PANEL.
ج.م.‏ 370.00

LM2596HVS DC to DC Adjustable Step Down Buck Converter Power Supply Module

03.00.24
Input voltage range: DC 4.5V to 53V (input voltage must be greater than the output voltage to 1.5V or more high. Could not boost)
ج.م.‏ 70.00

10 Position DIP Switch 2.54mm

04.00.70
CONTACT RESISTANCE : 50MΩ 24VDC/100MA (AT INITIAL);100MΠTYPICAL, 24VDC/100MA (AFTER LIFE TEST) : 100MΩ TYPICAL, 24VDC/100MA (AFTER LIFE TEST);EACH SIZE : 12 X 10 X 11 MM / 0.47" X 0.4" X 0.43" (L*W*H)
ج.م.‏ 10.00

Arduino mega2560 case For protection

03.03.30
Brand : Other Type : Electronic Accessories
ج.م.‏ 75.00

Bluetooth Module HC-05 , Serial TTL

03.02.26
The HC-05 is a class 2 Bluetooth module designed for transparent wireless serial communication. It is pre-configured as a slave Bluetooth device. Once it is paired to a master Bluetooth device such as PC, smartphone and tablet, its operation becomes transparent to the user. No user code specific to the Bluetooth module is needed at all in the user-microcontroller program.
ج.م.‏ 175.00

LCD1602 LCD monitor 1602 5V blue screen

03.01.31
Brand : Other Type : Electronic Accessories
ج.م.‏ 75.00

Reprap 3D Printer Arduino Mega Shield (RAMPS)

03.00.02
The RepRap Arduino-compatible MEGA Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
ج.م.‏ 190.00

SYB-170 Tie-Point Breadboard (White)

03.00.33
This 170 Tie Point Interlocking Solderless Breadboard is a cute mini size breadboard, good for small projects. It is 3.5cm x 4.7cm in size with a standard double-strip design. You can always "snap" these breadboards together either way to make longer or wider breadboards.[Specifications]Color : White170 Tie PointSelf adhesiveCan be interlocked for larger projectsHorizontal: 1-17Vertical: ...
ج.م.‏ 15.00

Ultrasonic Distance Measuring Sensor HC-SR04 Module for Arduino

03.00.41
Ultrasonic Distance Measuring Sensor HC-SR04 Module for Arduino
ج.م.‏ 50.00

6 Position DIP Switch 2.54mm

04.00.68
CONTACT RESISTANCE : 50MΩ 24VDC/100MA (AT INITIAL);100MΠTYPICAL, 24VDC/100MA (AFTER LIFE TEST) : 100MΩ TYPICAL, 24VDC/100MA (AFTER LIFE TEST);EACH SIZE : 12 X 10 X 11 MM / 0.47" X 0.4" X 0.43" (L*W*H)
ج.م.‏ 6.00

Arduino Nano Microcontroller ATmega328 Development Board

03.00.08
The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328. It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack (An will solved), and works with a Mini-B USB cable instead of a standard one. What's new: ATMEGA328 (more flash and ram memory) Blue power LED is on the top A0-A7 pins compatible with Arduino Stamp and Pro Mini Two layers PCB Lower cost Easier to hack the Eagle file Specifications Microcontroller: ATmega328 FT232RL Replace by CH340G Operating Voltage (logic level): 5 V Input Voltage (recommended): 7-12 V Input Voltage (limits): 6-20 V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 8 DC Current per I/O Pin: 40 mA Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB used by bootloader SRAM: 1 KB (ATmega168) or 2 KB (ATmega328) EEPROM: 512 bytes (ATmega168) or 1 KB (ATmega328) Clock Speed: 16 MHz Dimensions: 0.73" x 1.70" Length: 45 mm Width: 18 mm Weight: 5 g The Arduino Nano can be powered via the Mini-B USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source. Memory The ATmega328 has 32 KB, (also with 2 KB used for the bootloader). The ATmega328 has 2 KB of SRAM and 1 KB of EEPROM. Input and Output Each of the 14 digital pins on the Nano can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have specialized functions: Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data. These pins are connected to the corresponding pins of the FTDI USB-to-TTL Serial chip. External Interrupts: 2 and 3. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details. PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with the analogWrite() function. SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI communication, which, although provided by the underlying hardware, is not currently included in the Arduino language. LED: 13. There is a built-in LED connected to digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it's off. The Nano has 8 analog inputs, each of which provides 10 bits of resolution (i.e. 1024 different values). By default they measure from ground to 5 volts, though it is possible to change the upper end of their range using the analogReference() function. Analog pins 6 and 7 cannot be used as digital pins. Additionally, some pins have specialized functionality: I2C: A4 (SDA) and A5 (SCL). Support I2C (TWI) communication using the Wire library (documentation on the Wiring website). There are a couple of other pins on the board: AREF. Reference voltage for the analog inputs. Used with analogReference(). Reset. Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board. Communication The Arduino Nano has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega168 and ATmega328 provide UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An CH340G on the board channels this serial communication over USB and the FTDI drivers (included with the Arduino software) provide a virtual com port to software on the computer. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board. The RX and TX LEDs on the board will flash when data is being transmitted via the FTDI chip and USB connection to the computer (but not for serial communication on pins 0 and 1). A SoftwareSerial library allows for serial communication on any of the Nano's digital pins. The ATmega328 also support I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the I2C bus. Programming The Arduino Nano can be programmed with the Arduino software. Select "Arduino Diecimila, Duemilanove, or Nano w/ ATmega168" or "Arduino Duemilanove or Nano w/ ATmega328" from the Tools > Board menu (according to the microcontroller on your board). The ATmega168 or ATmega328 on the Arduino Nano comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the originalSTK500 protocol. You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar. Automatic (Software) Reset Rather than requiring a physical press of the reset button before an upload, the Arduino Nano is designed in a way that allows it to be reset by software running on a connected computer. One of the hardware flow control lines (DTR) of the FT232RL is connected to the reset line of the ATmega328 via a 100 nanofarad capacitor. When this line is asserted (taken low), the reset line drops long enough to reset the chip. The Arduino software uses this capability to allow you to upload code by simply pressing the upload button in the Arduino environment. This means that the bootloader can have a shorter timeout, as the lowering of DTR can be well-coordinated with the start of the upload. This setup has other implications. When the Nano is connected to either a computer running Mac OS X or Linux, it resets each time a connection is made to it from software (via USB). For the following half-second or so, the bootloader is running on the Nano. While it is programmed to ignore malformed data (i.e. anything besides an upload of new code), it will intercept the first few bytes of data sent to the board after a connection is opened. If a sketch running on the board receives one-time configuration or other data when it first starts, make sure that the software with which it communicates waits a second after opening the connection and before sending this data.
ج.م.‏ 165.00

Bluetooth Module HC-06 , Serial TTL

03.01.26
Bluetooth UART RS232 serial converter Module Operating Frequency Band 2.4GHz unlicensed ISM band Bluetooth Specification V2.0+EDR Output Power Class 2 Operating Voltage 3.3V Host Interface USB/UART Audio Interface None Flash Memory Size 8Mbit. Features: CSR Bluetooth Chip Solution Bluetooth v2.0+EDR Compliant UART interface and with baud rate setup function Built-in antenna. Coverage up to 30ft. Incredible small size with 3.3V input, and RoHS Compliant Working current: While pairing 30mA, paired 8mA Frequency: 2.4GHz ISM band Baud rate is 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 user manually set up. Default Baud Rate: 9600,8,1,n Support for 8Mbit External Flash Onboard Support for 802.11 Co-Existence Product Description Storage Temperature: -40 to 85 degrees Celsius Size : 28 mm x 15 mm x 2.35 mm Used for GPS navigation system, water and electricity gas Automatic Reading Meter, The industrial field in control system The factory default parameters: Baud rate: 9600, N, 8, 1. Pairing code: 1234 AT command set as follows: 1, Test communication Send: AT (return OK, A seconds press once again) Return: OK 2, Change Bluetooth serial interface communication baud rate Send: AT + BAUD1 Return: OK1200 Send: AT + BAUD2 Return: OK2400 1---------1200 2---------2400 3---------4800 4---------9600 5---------19200 6---------38400 7---------57600 8---------115200 9---------230400 A---------460800 B---------921600 C---------1382400 Not recommended in more than 115200 baud rate, the signal interference will make the system not stability 3, change bluetooth name Send: AT + NAMEname Return: OKname Parameter name: will set the current name, which was the name of the search to Bluetooth. Within 20 characters. Example: send AT + NAME bill_gates Back to OKname now Bluetooth name is bill_gates Parameters can power lost save, modify it only need once. The PAD service can see change Bluetooth name 4, Change Bluetooth pairing password Send: AT + PINxxxx Return: OKsetpin Example: send AT + PIN8888 Back to OKsetpin now Bluetooth pairing password is 8888, module's default password g is 1234. Parameters can power lost save, modify it only need once.
ج.م.‏ 185.00

Color Sensor Module (TCS230)

03.02.53
Color Sensor Module (TCS230) SINGLE-SUPPLY OPERATION (2.7V TO 5.5V) HIGH-RESOLUTION CONVERSION OF LIGHT INTENSITY TO FREQUENCY PROGRAMMABLE COLOR AND FULL-SCALE OUTPUT FREQUENCY POWER DOWN FEATURE COMMUNICATES DIRECTLY TO MICROCONTROLLER/ARDUINO S0~S1: OUTPUT FREQUENCY SCALING SELECTION INPUTS S2~S3: PHOTODIODE TYPE SELECTION INPUTS OUT PIN: OUTPUT FREQUENCY EO PIN: OUTPUT FREQUENCY ENABLE PIN (ACTIVE LOW)
ج.م.‏ 125.00

Raspberry Pi GPIO Breakout Board

03.00.105
Type : 3D Printer Accessories Brand : Other
ج.م.‏ 140.00

8 Position DIP Switch 2.54mm

04.00.69
8 Position DIP Switch 2.54mm
ج.م.‏ 6.00

Arduino 30 Amp Sensing & Controlling Current Flow Sensor Module Board

03.04.46
Current Sensor Module 20A range ACS712 The module can measure the positive and negative 20 amps, corresponding to the analog output 100mV / A; 1、The current sensor chips: ACS712ELC-20A ; 2、Pin 5V power supply, on-board power indicator; 3、The module can measure the positive and negative 20 amps, corresponding to the analog output 100mV / A; 4、No test current through the output voltage is VCC / 2; Note: ACS712 is based on the principle of the Hall test, please use this field to avoid impact
ج.م.‏ 110.00

Arduino Pro Mini Microcontroller ATmega328 Development Board 5.0V 16Mhz

03.00.20
The Arduino Pro Mini is a microcontroller board based on the ATmega328p. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers. A six pin header can be connected to a USB to serial adapter to provide USB power and communication to the board. The Arduino Pro Mini is intended for semi-permanent installation in objects or exhibitions. The board comes without pre-mounted headers, allowing the use of various types of connectors or direct soldering of wires. The pin layout is compatible with the Arduino Mini.
ج.م.‏ 130.00

Joystick Shield for Arduino

03.00.43
The SparkFun Joystick Shield Kit contains all the parts you need to enable your Arduino with a joystick! The shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button) and a two-axis thumb joystick gives your Arduino functionality on the level of old Nintendo controllers. Soldering is required, but it’s relatively easy and requires minimal tools.
ج.م.‏ 160.00

SYB-170 Tie-Point Breadboard (Blue )

03.01.33
This 170 Tie Point Interlocking Solderless Breadboard is a cute mini size breadboard, good for small projects. It is 3.5cm x 4.7cm in size with a standard double-strip design. You can always "snap" these breadboards together either way to make longer or wider breadboards.[Specifications]Color : Blue170 Tie PointSelf adhesiveCan be interlocked for larger projectsHorizontal: 1-17Vertical: ...
ج.م.‏ 15.00

5mW Laser Module emitter - Red Line

03.01.52
Specifications Output Power: Min 2.5mW, Typical 3.0mW, Max 5.0mW Working current: Min 10mA, Typical 20mA, Max 25mA Working voltage: Min 2.3VDC, Typical 4.5VDC, Max 8.0VDC Wavelength: 650nm Working Temperature: Min -15℃, Typical 25℃, Max 35℃ Storage Temperature: Min -20℃, Max +25℃ Focused Dot width:<2mm spotting 3 meters away. Outline Dimension: 12mm(Diameter) x 35mm(Length) Practical test for point head: reflection visible to random target >1000m Cautions: Class III, avoid direct eye exposure to beams.
ج.م.‏ 85.00

Arduino UNO CNC Shield v3

03.00.99
This board is widely used for driver expansion board of engraving machin. There are total 4 ways slots for stepper motor driver modules (Model A4988 - It sold separately at our store ), and it can drive 4 ways stepper motors each up to 2A. Each way stepper motor has two I/O ports and it means 6 I/O ports can manage 3 stepper motors. It is very convenient to operate.
ج.م.‏ 160.00

Slide Type Switch Module 1-Bit 2.54mm 1 Position Way DIP Red Pitch

04.00.65
Slide Type Switch Module 1-Bit 2.54mm 1 Position Way DIP Red Pitch
ج.م.‏ 10.00

SYB-400 Tie-Point Breadboard

06.0000.05
This mini universal solderless breadboard is composed of ABS plastic and tin phosphorus plated bronze contact chips, it has 400 contacts tie-points available. It can work with 20-29AWG wire, perfect for circuit prototype design.Type: Mini Solderless BreadboardModel: BB-801Available Contacts Tie-points: 400Material: ABS Plastic & Tin Phosphorus Plated Bronze Contact ChipVoltage: 300VElectric ...
ج.م.‏ 25.00

Arduino Nano Micro USB CH340 3.0 ATmega328P Controller Board Yellow

03.00.15
Micro USB socket - Due to Micro USB socket you can use regular mobile data cableColor - yellow CH340G Replace FT232RLOperating Voltage(logic level):5V8 analog inputs ports:A0 - A714 Digital input / output ports:TX,RX,D2 ~ D136 PWM ports:D3, D5, D6, D9, D10, D111 pairs of TTL level serial transceiver ports RX / TXUsing Atmel Atmega328P-AU
ج.م.‏ 165.00

Serial Converter TTL UART on CP2102 USB Module Board

03.03.46
CP2102 its high integration, built-in USB2.0 full-speed function controller, USB transceiver, crystal oscillator, EEPROM, and asynchronous serial data bus (UART), supports full-featured modem signals, without any external USB device. CP2102 with other USB-UART adapter circuit works similar to the PC through the driver's USB port into a virtual COM port in order to achieve the purpose of expansion.
ج.م.‏ 95.00

Servo Motor"SG90"

03.00.28
OPERATING VOLTAGE : 4.8~6.0V OPERATING SPEED : 0.12SEC/60 DEGREE(4.8V)~0.1SEC/60 DEGREE(6.0V) TORQUE : 1.6KG/CM(4.8V) TEMPERATURE RANGE : -30~+60℃ SERVO TYPE : ANALOG SERVO DIMENSION: 22.3 X11.8X26.3 MM. KIT INCLUDES SET OF 6 PIECES OF ARM SERVO HORN WITH DIFFERENT SIZES AND SHAPES, HORN MOUNTING SCREWS,SERVO MOUNTING SCREWS.
ج.م.‏ 85.00

3-Axis Gyroscope & Accelerometer Module GY-521 - 16-Bit Digital Output, I2C Interface - MPU6050

GY-521 MPU6050 6DOF 3-Axis Gyroscope and Accelerometer Module is a carrier board based on MPU-6050 sensor which contains an accelerometer and a gyroscope. MPU-6050 sensor contains a MEMS accelerometer and a MEMS gyro in a single chip. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel. Therefore it captures the x, y, and z channel at the same time. The sensor uses the I2C-bus to interface with microcontrollers.
ج.م.‏ 95.00

DC 2.1mm Power Female Plug with Wire

06.12.05
ج.م.‏ 7.00

40PCS Jumper wire Cable 1P-1P Male to Male -length 20cm- arduino

06.14.05
Brand : Arduino Type : Electronic Accessories
ج.م.‏ 22.00

ARDUINO SENSOR SHIELD V5

03.01.50
This Arduino Sensor Shield V5.0 sensor expansion board, the motherboard is not only extended out the Arduino Uno all digits and analog interface to servo line order form , but also add hoc IIC interface, servo controller interface, Bluetooth module communication interface, SD card module communication interface, APC220 radio frequency module communication interface, ultrasonic sensor interface, 12864 LCD serial and parallel interfaces, independent expansion will be more easy and convenient. Arduino Sensor Shield V5.0 for digital analog module and servos. The Arduino Sensor Shield V5.0 allows plug and play connection to various modules like sensors, servos, relays, buttons, potentiometers and more. Features: I2C interface Bluetooth module communication interface SD card module communication interface APC220 wireless RF modules communication interface RB URF V1.1 ultrasonic sensors interface 12864 LCD serial and parallel interface 32 servo controller interfaces Specs: Dimensions: 57x57x18.5mm Weight: 23g
ج.م.‏ 65.00

IR Infrared Obstacle Avoidance Sensor Module for Arduino

03.00.42
IR Infrared Obstacle Avoidance Sensor Module for Arduino THE SENSOR MODULE ADAPTABLE TO AMBIENT LIGHT, HAVING A PAIR OF INFRARED EMITTING AND RECEIVING TUBES, TRANSMITTING TUBES EMIT INFRARED CERTAIN FREQUENCY, WHEN THE DIRECTION OF AN OBSTACLE IS DETECTED (REFLECTION SURFACE), THE INFRARED REFLECTED IS RECEIVED BY THE RECEPTION TUBE, AFTER A COMPARATOR CIRCUIT PROCESSING, THE GREEN LIGHT IS ON, BUT THE SIGNAL OUTPUT INTERFACE OUTPUT DIGITAL SIGNAL (A LOW-LEVEL SIGNAL), YOU CAN ADJUST THE DETECTION DISTANCE KNOB POTENTIOMETER, THE EFFECTIVE DISTANCE RANGE OF 2 ~ 30CM, THE WORKING VOLTAGE OF 3.3V- 5V. DETECTION RANGE OF THE SENSOR CAN BE OBTAINED BY ADJUSTING POTENTIOMETER, WITH LITTLE INTERFERENCE, EASY TO ASSEMBLE, EASY TO USE FEATURES, CAN BE WIDELY USED IN ROBOT OBSTACLE AVOIDANCE, AVOIDANCE CAR, LINE COUNT, AND BLACK AND WHITE LINE TRACKING AND MANY OTHER OCCASIONS.
ج.م.‏ 60.00

Laser sensor Module 650nm 6mm 5V 5mW Red Laser Dot Diode KY-008 for Arduino

03.01.38
LASER SENSOR MODULE 650NM 6MM 5V 5MW RED LASER DOT DIODE KY-008 FOR ARDUINO OPERATING VOLTAGE 5V POWER 5MW WAVELENGTH 650NM
ج.م.‏ 60.00

Limit Switch (Roller Lever)

04.00.62
LIMIT SWITCHES SERVE AS THE MECHANISM THAT TELLS THE COMPUTER THE LIMITS OF THE 3D PRINTERS & CNC MACHINE. WHEN ONE OF THE AXES MOVES TO AN AXIS LIMIT, THE SWITCH IS ACTIVATED AND THE MACHINE STOPS.
ج.م.‏ 12.00

AC Power Connector With On/Off Switch - Panel Mound

06.08.02
IEC POWER JACK FOR CHASSIS MOUNT WITH 10A FUSE HOLDER FOR CLIP USE AND ON/OFF SWITCH, BLACK. REGULAR VOLTAGE: 250V / 10A TEMP.: -40° +-80°
ج.م.‏ 26.00

Bigtreetech New 3D printer hot bed Power expansion board/MOS tube high current load module for 3D printer

This module can be used in both Chitu motherboard. The motherboard shows in the pictures is NOT included in the shipping list.
ج.م.‏ 150.00

NodeMCU v2 - Lua based ESP8266 development kit

03.00.40
NodeMCU is an open source development board and firmware based in the widely used ESP8266 -12E WiFi module. It allows you to program the ESP8266 WiFi module with the simple and powerful LUA programming language or Arduino IDE. With just a few lines of code you can establish a WiFi connection and define input/output pins according to your needs exactly like arduino, turning your ESP8266 into a web server and a lot more. It is the WiFi equivalent of ethernet module. Now you have internet of things (iot) real tool. With its USB-TTL , the nodeMCU Dev board supports directly flashing from USB port. It combines features of WIFI accesspoint and station + microcontroller. These features make the NodeMCU extremly powerful tool for Wifi networking. It can be used as access point and/or station, host a webserver or connect to internet to fetch or upload data. Features Programable WiFi module. Arduino-like (software defined) hardware IO. Can be programmed with the simple and powerful Lua programming language or Arduino IDE. USB-TTL included, plug & play. 10 GPIOs D0-D10, PWM functionality, IIC and SPI communication, 1-Wire and ADC A0 etc. all in one board. Wifi networking (can be used as access point and/or station, host a web server), connect to internet to fetch or upload data. Event-driven API for network applications. PCB antenna
ج.م.‏ 195.00

AC POWER CONNECTOR WITH FUSE HOLDER

06.08.03
AC POWER CONNECTOR WITH FUSE HOLDER CHASSIS MOUNT TYPE , USE WITH NORMAL AC POWER CABLE LIKE PC POWER CORD.
ج.م.‏ 13.00

ARDUINO NANO EXPANSION BOARD ADAPTER

03.0000.23
Arduino Nano Sensor Expansion Board This board is designed for Arduino NANO IO(Input Output) Expansion Shield to facilitate an easy connection between Arduino Nano Board and many other devices. This board is compatible with Arduino Nano version 2 and version 3.
ج.م.‏ 65.00

Arduino Pro Micro 5V 16MHz Board using ATmega32U4 - Micro USB

03.00.18
ATMega32U4 running at 5V/16MHzSupported under IDE v1.0.1On-Board micro-USB connector for programming4 x 10-bit ADC pins12 x Digital I/Os (5 are PWM capable)Rx and Tx Hardware Serial Connections
ج.م.‏ 310.00

Male to Male Solderless Flexible Breadboard Jumper Cable Wires - 65Pcs

06.13.05
65PCS MALE TO MALE SOLDERLESS FLEXIBLE BREADBOARD JUMPER CABLE WIRES
ج.م.‏ 30.00

Sound Detection Sensor Module Sensor Intelligent Vehicle For Arduino car

03.00.46
Sound Detection Sensor Module Sensor Intelligent Vehicle For Arduino car CAN BE USED FOR ACOUSTIC CONTROL LIGHT; GIVE SOUND AND LIGHT ALARM WORKING WITH PHOTOSENSITIVE SENSOR
ج.م.‏ 75.00

AC POWER CONNECTOR WITH FUSE HOLDER AND SWITCH

06.23.10
AC POWER CONNECTOR WITH FUSE HOLDER AND ON/OFF SWITCH CHASSIS MOUNT TYPE, USE WITH NORMAL AC POWER CABLE LIKE PC POWER CORD.
ج.م.‏ 26.00

Arduino DHT11 Temperature and Humidity Sensor Module Board

03.02.29
Arduino DHT11 Temperature and Humidity Sensor Module Board Can detect surrounding environment of the humidity and temperature Humidity measurement range: 20 Percent Minus 95 Percent, humidity measurement error: Plus Minus 5 Percent Temperature measurement range: 0 to 50 ;measurement error: Plus Minus 2 degrees Working voltage 3.3 ~ 5V Output form: digital output Has fixed bolt hole and easy installation PCB size: 3.1cm x 1.4cm Can detect surrounding environment of the humidity and temperature Humidity measurement range: 20 Percent Minus 95 Percent, humidity measurement error: Plus Minus 5 Percent Temperature measurement range: 0 to 50 ;measurement error: Plus Minus 2 degrees Working voltage 3.3 ~ 5V Output form: digital output Has fixed bolt hole and easy installation PCB size: 3.1cm x 1.4cm DHT11 Temperature and Humidity Sensor features a temperature and humidity sensor complex with a calibrated digital signal output. By using the exclusive digital signal acquisition technique and temperature and humidity sensing technology, it ensures high reliability and excellent long term stability. This sensor includes a resistive type humidity measurement component and an NTC temperature measurement component, and connects to a high-performance 8bit microcontroller, offering excellent quality, fast response, anti interference ability
ج.م.‏ 50.00

Arduino Pro Micro 5V 16MHz Board using ATmega32U4 - Mini USB

03.00.17
ATMega32U4 running at 5V/16MHzSupported under for Arduino IDE v1.0.1On-Board MINI USB connector for programming4 x 10-bit ADC pins12 x Digital I/Os (5 are PWM capable)Rx and Tx Hardware Serial Connections The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface. This tiny little board does all of the neat-o Arduino tricks that you're familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx. Running at 16MHz and 5V, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere. There is a voltage regulator on board so it can accept voltage up to 12VDC. If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC. This latest revision corrects the silk error from the last version of the board so that pin 14 is correctly labeled. We've also added a PTC fuse and diode protection to the power circuit and corrected the RX and TX LED circuit. Features: ATmega32U4 running at 16MHz with external resonator (0.5% tolerance) On-Board micro-USB connection Supported under Arduino IDE v1.0.1 4 x 10-bit ADC pins 12 x Digital I/Os (5 are PWM capable) Operating Voltage (logic level): 5 V Input Voltage (recommended): 7-12 V, or 5V via USB cable Rx and Tx Hardware Serial Connections Dimensions: 0.7x1.3" (18x33mm) Less than 2 grams Package Including 1pc Arduino Pro Micro ATmega32U4 5V 16MHz 1pc of Micro-USB cable Documents and Downloads Arduino Pro Micro Driver Windows Driver Installation Guide Linux / Mac Driver Installation Guide
ج.م.‏ 255.00

Arduino nano USB V3.0 ATmega328P 5V 16M Micro-controller board

03.01.10
The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x) or ATmega168 (Arduino Nano 2.x). It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one. The Nano was designed and is being produced by Gravitech.
ج.م.‏ 160.00